Stack and reach
How high and how far forward the top of the head tube is, from the bottom bracket. They are the two numbers that decide whether a frame can be set up like yours.
BB, or bottom bracket
The axle your cranks turn on, in the middle of the frame. Every number on this site is measured from it, because it is the one point that sits in the same place on every bike.
Headset cover
The little cap on top of the head tube, under your spacers. Most makers do not publish it, so I assume 10 mm and add 6 mm to the band beside every answer.
Stem clamp, and its centre
The collar on the steerer that your stem bolts to. I need the middle of it. Where a maker gives only the height, I assume halfway up and say so on the answer.
Steerer
The tube coming up out of the fork. The cover, the spacers and the stem all sit on it, and it is the thing a mechanic cuts to length.
Bar reach
How far forward the hoods sit from the middle of the bar. Two bars on the same stem can put your hands 20 mm apart, which is why I ask.
Setback
How far your saddle sits behind the bottom bracket.
Drop
How much lower your hands sit than your saddle. On a riser bar I count the bar's rise, so the drop is that much less than it is to the clamp.
Rails, and the rail centre
The two rods under your saddle, and the middle of the straight part of them. That midpoint is the point I use, because it is the one you can find with a tape.
The band
How far out I could be, in millimetres, and why. It is a straight sum of everything I had to assume rather than a clever average, so it errs wide on purpose.
wb, stand, trail
Wheelbase, standover and trail: how long the bike is, how high the top tube is where you straddle it, and how steady the steering feels. I show them against your bike, and I leave them out when the maker does not publish them.
est.
Estimated: a number I worked out rather than read off the maker's table. Anything marked this way can move if the maker publishes the real one.
Close Escape closes it. The measuring guide has the pictures. Open the measuring guide
ICAN FL1
Road · 5 sizes
Sign in and add the bike you ride, and this table will say what each size needs for your position.
Sign in
This is the bike I ride
No account is needed to read the table. Report a wrong number · Correct this bike
- Bike
- ICAN FL1 · Road · 5 sizes
- Geometry
- icanbikes.com, fetched 22 Oct 2026, read off the maker's chart, re-checked, no differences
- Seat angle convention
- Calculated from ICAN's table
- Cockpit
- Generic stem and bar, assumed
- Solved with
- cover 10 mm (assumed), max spacers 40 mm (assumed), stem clamp centre 20 mm (assumed), so every verdict carries ±10 mm at the bar
- Sheet
- 22 October 2026 · 879 bikes, 79 makes, 4,979 sizes in the catalogue
Geometry, every size, from the maker's table
The tinted row is the size drawn beside it. Press a size to draw it.| Size | Stack (mm) | Reach (mm) | Head angle (deg) | Seat angle (deg) | Head tube (mm) | Chainstay (mm) | Wheelbase (mm) | Standover (mm) |
|---|---|---|---|---|---|---|---|---|
| 49 | 514.2 | 375 | 71.75 | 75.5 | 107 | 410 | 970 | 700 |
| 52 | 527.2 | 380 | 72.5 | 74 | 118 | 410 | 972.3 | 718 |
| 54 | 544 | 384 | 73 | 74 | 135 | 410 | 977.9 | 738 |
| 56 | 564.8 | 395 | 73.5 | 73.5 | 155 | 410 | 990.5 | 760 |
| 58 | 590.7 | 402 | 73.5 | 73.5 | 182 | 410 | 1005.2 | 784 |
The table runs on to the right: 6 more columns after Reach. Scroll it sideways to read them.
The 54 drawn to scale from the table, with no build on it. Stack and reach run from the bottom bracket to the top of the head tube; every size is solved from those two. One square is 100 mm.
The maker's cockpit
No stock cockpit I can name, so every size is solved on a generic stem and bar unless you choose one on the sheet.Generic stem and barAssumedNo bar is listed for this frame.
Frame facts
read off the maker's page: icanbikes.com- Tyre clearance
- 32 mm
- Bottom bracket
- T47
- Axles and brakes
- 12x100 / 12x142
- UDH
- not published
- Seatpost
- 27.2 mm round
- Frame weight
- 795 g, size 54cm
In the maker's words
Kept whole, as I read it off icanbikes.com.The page's spec names handlebar "HB-22, 400*100mm" (ICAN's own bar; 400 mm wide, 100 mm) and seatpost "SP01, 27.2*400mm"; headset 1-1/2 in top and bottom, fits FSA NO.55R.
Cockpit and seatpost, in the maker's words · 38 words
The page's spec names handlebar "HB-22, 400*100mm" (ICAN's own bar; 400 mm wide, 100 mm) and seatpost "SP01, 27.2*400mm"; headset 1-1/2 in top and bottom, fits FSA NO.55R. No per-size stem length printed, so stock fields are null.
SOURCE: icanbikes.com is ICAN's second English site (WordPress, "Products-list" pages), beside the Shopify store icancycling.com that the other ICAN files cite. Source: image_table (maker's own site icanbikes.com; geometry published only as the image
How I read the maker's table
both carry the same A9, A23 and TRA01 frames under the ICAN name, and the frame below is on icanbikes.com only (not in icancycling.com's product sitemap, fetched 22 Oct 2026). The page "Carbon Frame Road Bike | Carbon Disc Road Frameset | ICAN FL1" (URL "t1000-carbon-road-disc-brake-frame-fl1-795g"; image uploaded Jul 2024; Bike Insights files the FL1 under 2023; no model year printed, model_year null). Columns as printed, sizes 49/52/54/56/58: TTL (drawn horizontal: top_tube_effective), STL, STA, HTL, HTA, RC 410, BBH (BB drop) 74/74/72/72/72, AEP (BB height 272/272/274/274/274, not in the schema), AB (drawn from the top tube down to the ground: standover), FL fork length 371 (not in the schema), FR fork rake 44, REACH, STACK, FC, WB. No trail printed. Spec table: Full carbon Toray T1000 and T800, UD black, handlebar "HB-22, 400*100mm", seatpost "SP01, 27.2*400mm", BB T47, headset "Top 1-1/2 in, Down 1-1/2 in (fit FSA NO.55R)", thru axle front 100*12 / rear 142*12mm, max tire 32mm, weight "795+_40g (54cm)", disc front 140/160mm and rear 140mm, EN and UCI tests (a UCI frameset label is shown in the gallery).
Source: image_table (maker's own site icanbikes.com; geometry published only as the image https://www.icanbikes.com/wp-content/uploads/2024/07/20240702161354.jpg, 2136x1590 px, a CAD drawing over a table; read by eye, image NOT stored)
