Stack and reach
How high and how far forward the top of the head tube is, from the bottom bracket. They are the two numbers that decide whether a frame can be set up like yours.
BB, or bottom bracket
The axle your cranks turn on, in the middle of the frame. Every number on this site is measured from it, because it is the one point that sits in the same place on every bike.
Headset cover
The little cap on top of the head tube, under your spacers. Most makers do not publish it, so I assume 10 mm and add 6 mm to the band beside every answer.
Stem clamp, and its centre
The collar on the steerer that your stem bolts to. I need the middle of it. Where a maker gives only the height, I assume halfway up and say so on the answer.
Steerer
The tube coming up out of the fork. The cover, the spacers and the stem all sit on it, and it is the thing a mechanic cuts to length.
Bar reach
How far forward the hoods sit from the middle of the bar. Two bars on the same stem can put your hands 20 mm apart, which is why I ask.
Setback
How far your saddle sits behind the bottom bracket.
Drop
How much lower your hands sit than your saddle. On a riser bar I count the bar's rise, so the drop is that much less than it is to the clamp.
Rails, and the rail centre
The two rods under your saddle, and the middle of the straight part of them. That midpoint is the point I use, because it is the one you can find with a tape.
The band
How far out I could be, in millimetres, and why. It is a straight sum of everything I had to assume rather than a clever average, so it errs wide on purpose.
wb, stand, trail
Wheelbase, standover and trail: how long the bike is, how high the top tube is where you straddle it, and how steady the steering feels. I show them against your bike, and I leave them out when the maker does not publish them.
est.
Estimated: a number I worked out rather than read off the maker's table. Anything marked this way can move if the maker publishes the real one.
Close Escape closes it. The measuring guide has the pictures. Open the measuring guide
De Rosa Merak
Road · 8 sizes
Sign in and add the bike you ride, and this table will say what each size needs for your position.
Sign in
This is the bike I ride
No account is needed to read the table. Report a wrong number · Correct this bike
- Bike
- De Rosa Merak · Road · 8 sizes · integrated cockpit
- Versions
- 2026, this table · 2022
- Geometry
- derosa.it, fetched 20 Oct 2026, re-checked, no differences
- Seat angle convention
- Calculated from De Rosa's table
- Cockpit
- Generic stem and bar, assumed
- Solved with
- cover 10 mm (assumed), max spacers 40 mm (assumed), stem clamp centre 20 mm (assumed), so every verdict carries ±10 mm at the bar
- Sheet
- 22 October 2026 · 879 bikes, 79 makes, 4,979 sizes in the catalogue
Geometry, every size, from the maker's table
The tinted row is the size drawn beside it. Press a size to draw it.| Size | Stack (mm) | Reach (mm) | Head angle (deg) | Seat angle (deg) | Head tube (mm) | Chainstay (mm) | Wheelbase (mm) | Standover (mm)not published |
|---|---|---|---|---|---|---|---|---|
| 425 | 507 | 371 | 70.7 | 74.9 | 107 | 405 | 970.6 | |
| 445 | 513 | 376 | 71.4 | 74.5 | 110.6 | 405 | 971.6 | |
| 465 | 524 | 380 | 72 | 74.1 | 120 | 405 | 973.7 | |
| 480 | 537 | 385 | 72.6 | 73.9 | 131.6 | 405 | 977.7 | |
| 505 | 548 | 393 | 73 | 73.9 | 141.5 | 405 | 984.7 | |
| 525 | 561 | 399 | 73.1 | 73.7 | 154.7 | 405 | 993.8 | |
| 545 | 574 | 406 | 73.3 | 73.5 | 167.6 | 405 | 1002.9 | |
| 565 | 591 | 409 | 73.4 | 73.1 | 185 | 405 | 1009.9 |
The table runs on to the right: 6 more columns after Reach. Scroll it sideways to read them.
The 505 drawn to scale from the table, with no build on it. Stack and reach run from the bottom bracket to the top of the head tube; every size is solved from those two. One square is 100 mm. A dashed tube is a number the maker left out (est.).
The maker's cockpit
No stock cockpit I can name, so every size is solved on a generic stem and bar unless you choose one on the sheet.Generic stem and barAssumedNo bar is listed for this frame.
Frame facts
not read off the maker's page yet: derosa.it- Tyre clearance
- not recorded yet
- Bottom bracket
- not recorded yet
- Axles and brakes
- not recorded yet
- UDH
- not recorded yet
- Seatpost
- not recorded yet
- Frame weight
- not recorded yet
In the maker's words
Kept whole, as I read it off derosa.it.De Rosa x Vision integrated handlebar, the Merak page's "HandleBar Geometry" sheet (https://derosa.it/app/uploads/2026/09/Merak_Bar_Width.pdf): sold as width x stem "380x90, 400x90, 380x100, 400x100, 420x100, 380x110, 400x110, 420x110, 380x120, 400x120, 420x120, 380x130, 400x130, 420x130, 380x140, 400x140, 420x140" ("Stem/Hb Reach"), i.e.
Cockpit and seatpost, in the maker's words · 83 words
De Rosa x Vision integrated handlebar, the Merak page's "HandleBar Geometry" sheet (https://derosa.it/app/uploads/2026/09/Merak_Bar_Width.pdf): sold as width x stem "380x90, 400x90, 380x100, 400x100, 420x100, 380x110, 400x110, 420x110, 380x120, 400x120, 420x120, 380x130, 400x130, 420x130, 380x140, 400x140, 420x140" ("Stem/Hb Reach"), i.e. stem lengths 90/100/110/120/130/140 mm; reach 75 mm; drop 115 mm; shifter width printed "38 mm, 40 mm, 42 mm" (read as 380/400/420, the widths the pairs use); bar width at the drops 410/430/450 mm. The sheet prints no stem angle. See the bar file de-rosa-merak-vision-cockpit.json.
OFFICIAL SOURCE: De Rosa's Merak page (https://derosa.it/model/merak-2026/), the "Geometries" table. Source: html table (official De Rosa model page, section "Geometries": the table in the page markup; fetched 2026-10-20
How I read the maker's table
Not published, so null: seat tube length, standover, trail, stock stem and bar per size; the page names no stock tyre (tyre_width_mm null). Column letters from the drawing beside the table (read only for its letters, not stored; white lines on a transparent ground): ET is drawn horizontal at head tube top height from the seat tube line to the head tube line (top_tube_effective); HS head tube; SA seat angle; HA head angle; G BB drop; RC rear centre, BB to rear axle (chainstay); FC front centre; WB wheelbase; F fork length, axle to crown, 371 on every size (not in the schema); OT fork offset; STACK and REACH drawn from the BB to the top of the head tube (stack_datum null: no words about a cover). The drawing also letters ST (seat tube) and prints R350,00 arcs, but the table has no ST column, so seat_tube_length is null; the Size column (425 to 565) is the maker's size name. The page's model name carries the year 2026 (model_year 2026). The "70" page (https://derosa.it/model/70/, fetched once, HTTP 200) prints this same table's numbers under mislabelled headers ("B (cm)" 50.8, "C (cm)" 405, ...) without a head angle, so the 70 has no file of its own.
Source: html table (official De Rosa model page, section "Geometries": the table in the page markup; fetched 2026-10-20, HTTP 200)